Kernel driver `w83781d.o' ========================= Status: W83781D support is complete and well-tested. W83782D support is complete and well-tested. W83783S support is complete but has not been well-tested. W83791D support is BETA. W83627HF support is complete but has not been well-tested. AS99127F support is BETA and has known problems due to lack of a chip datasheet. SEE BELOW. Supported chips: * Winbond W83781D Prefix: 'w83781d' Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83781d.pdf * Winbond W83782D Prefix: 'w83782d' Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: http://www.winbond.com/PDF/sheet/w83782d.pdf * Winbond W83783S Prefix: 'w83783s' Addresses scanned: I2C 0x2d Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83783s.pdf * Winbond W83791D Prefix: 'w83791d' Addresses scanned: I2C 0x2c - 0x2f Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83791d.pdf * Winbond W83627HF Prefix: 'w83627hf' Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports) Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf * Asus AS99127F Prefix: 'as99127f' Addresses scanned: I2C 0x28 - 0x2f Datasheet: Unavailable from Asus Authors: Frodo Looijaard , Philip Edelbrock , and Mark Studebaker Module Parameters ----------------- * force: short array (min = 1, max = 48) List of adapter,address pairs to boldly assume to be present * force_w83781d: short array (min = 1, max = 48) List of adapter,address pairs which are unquestionably assumed to contain a `w83781d' chip * force_w83782d: Ditto * force_w83783s: Ditto * force_w83791d: Ditto * force_w83627hf: Ditto * force_as99127f: Ditto * force_subclients=bus,caddr,saddr,saddr This is used to force the i2c addresses for subclients of a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b' to force the subclients of chip 0x2d on bus 0 to i2c addresses 0x4a and 0x4b. This parameter is useful for certain Tyan boards. * ignore: short array (min = 1, max = 48) List of adapter,address pairs not to scan * ignore_range: short array (min = 1, max = 48) List of adapter,start-addr,end-addr triples not to scan * probe: short array (min = 1, max = 48) List of adapter,address pairs to scan additionally * probe_range: short array (min = 1, max = 48) List of adapter,start-addr,end-addr triples to scan additionally * init=[0,1] (default 1) Use 'init=0' to bypass initializing the chip. Try this if your computer crashes when you load the module. Description ----------- This driver implements support for the Winbond W83781D, W83782D, W83783S, W83791D, W83627HF and W83698HF chips, and the Asus AS99127F chips. We will refer to them collectively as W8378* chips. There is quite some difference between these chips, but they are similar enough that it was sensible to put them together in one driver. The W83627HF chip is assumed to be identical to the ISA W83782D. The Asus chips are similar to an I2C-only W83782D. Detection of these chips can sometimes be foiled because they can be in an internal state that allows no clean access. If you know the address of the chip, use a 'force' parameter; this will put them into a more well-behaved state first. The W8378* implements temperature sensors (three on the W83781D and W83782D, two on the W83783S), three fan rotation speed sensors, voltage sensors (seven on the W83781D, nine on the W83782D and six on the W83783S), VID lines, alarms with beep warnings, and some miscellaneous stuff. Temperatures are measured in degrees Celsius. There is always one main temperature sensor, and one (W83783S) or two (W83781D and W83782D) other sensors. An alarm is triggered for the main sensor once when the Overtemperature Shutdown limit is crossed; it is triggered again as soon as it drops below the Hysteresis value. A more useful behaviour can be found by setting the Hysteresis value to +127 degrees Celsius; in this case, alarms are issued during all the time when the actual temperature is above the Overtemperature Shutdown value. The driver sets the hysteresis value for temp1 to 127 at initialization. For the other temperature sensor(s), an alarm is triggered when the temperature gets higher then the Overtemperature Shutdown value; it stays on until the temperature falls below the Hysteresis value. But on the W83781D, there is only one alarm that functions for both other sensors! Temperatures are guaranteed within a range of -55 to +125 degrees. The main temperature sensors has a resolution of 1 degree; the other sensor(s) of 0.5 degree. Fan rotation speeds are reported in RPM (rotations per minute). An alarm is triggered if the rotation speed has dropped below a programmable limit. Fan readings can be divided by a programmable divider (1, 2, 4 or 8 for the W83781D; 1, 2, 4, 8, 16, 32, 64 or 128 for the others) to give the readings more range or accuracy. Not all RPM values can accurately be represented, so some rounding is done. With a divider of 2, the lowest representable value is around 2600 RPM. Voltage sensors (also known as IN sensors) report their values in volts. An alarm is triggered if the voltage has crossed a programmable minimum or maximum limit. Note that minimum in this case always means 'closest to zero'; this is important for negative voltage measurements. All voltage inputs can measure voltages between 0 and 4.08 volts, with a resolution of 0.016 volt. The VID lines encode the core voltage value: the voltage level your processor should work with. This is hardcoded by the mainboard and/or processor itself. It is a value in volts. When it is unconnected, you will often find the value 3.50 V here. The W83782D and W83783S temperature conversion machine understands about several kinds of temperature probes. You can program the so-called beta value in the sensor files. '1' is the PII/Celeron diode, '2' is the TN3904 transistor, and 3435 the default thermistor value. Other values are (not yet) supported. You can program your own values through the rt interface, but this is not very useful, because these tables are under NDA. In addition to the alarms described above, there is a CHAS alarm on the chips which triggers if your computer case is open. When an alarm goes off, you can be warned by a beeping signal through your computer speaker. It is possible to enable all beeping globally, or only the beeping for some alarms. Individual alarm and beep bits: 0x000001: in0 0x000002: in1 0x000004: in2 0x000008: in3 0x000010: temp1 0x000020: temp2 (+temp3 on W83781D) 0x000040: fan1 0x000080: fan2 0x000100: in4 0x000200: in5 0x000400: in6 0x000800: fan3 0x001000: chassis 0x002000: temp3 (W83782D and W83627HF only) 0x010000: in7 (W83782D and W83627HF only) 0x020000: in8 (W83782D and W83627HF only) If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already have disappeared! Note that in the current implementation, all hardware registers are read whenever any data is read (unless it is less than 1.5 seconds since the last update). This means that you can easily miss once-only alarms. The chips only update values each 1.5 seconds; reading them more often will do no harm, but will return 'old' values. AS99127F PROBLEMS ----------------- The as99127f support was developed without the benefit of a datasheet. In most cases it is treated as a w83781d (although revision 2 of the AS9917F looks more like a w83782d). This support will be BETA until a datasheet is released. One user has reported problems with fans stopping occasionally. Note that the individual beep bits are inverted from the other chips. The driver now takes care of this so that user-space applications don't have to know about it. Known problems: - Problems with diode/thermistor settings (supported?) - One user reports fans stopping under high server load. - Revision 2 seems to have 2 PWM registers but we don't know how to handle them. More details below. These will not be fixed unless we get a datasheet. If you have problems, please lobby Asus to release a datasheet. Unfortunately several others have without success. Please do not send mail to us asking for better as99127f support. We have done the best we can without a datasheet. Please do not send mail to the author or the sensors group asking for a datasheet or ideas on how to convince Asus. We can't help. Chip Features ------------- Chip `w83781d' LABEL LABEL CLASS COMPUTE CLASS ACCESS MAGNITUDE in0 NONE NONE R 2 in1 NONE NONE R 2 in2 NONE NONE R 2 in3 NONE NONE R 2 in4 NONE NONE R 2 in5 NONE NONE R 2 in6 NONE NONE R 2 in0_min in0 in0 RW 2 in1_min in1 in1 RW 2 in2_min in2 in2 RW 2 in3_min in3 in3 RW 2 in4_min in4 in4 RW 2 in5_min in5 in5 RW 2 in6_min in6 in6 RW 2 in0_max in0 in0 RW 2 in1_max in1 in1 RW 2 in2_max in2 in2 RW 2 in3_max in3 in3 RW 2 in4_max in4 in4 RW 2 in5_max in5 in5 RW 2 in6_max in6 in6 RW 2 fan1 NONE NONE R 0 fan2 NONE NONE R 0 fan3 NONE NONE R 0 fan1_min fan1 NONE RW 0 fan2_min fan2 NONE RW 0 fan3_min fan3 NONE RW 0 temp1 NONE NONE R 1 temp1_hyst temp1 temp1 RW 1 temp1_over temp1 temp1 RW 1 temp2 NONE NONE R 1 temp2_hyst temp2 temp2 RW 1 temp2_over temp2 temp2 RW 1 temp3 NONE NONE R 1 temp3_hyst temp3 temp3 RW 1 temp3_over temp3 temp3 RW 1 vid NONE NONE R 2 fan1_div fan1 NONE RW 0 fan2_div fan2 NONE RW 0 fan3_div fan3 NONE R 0 alarms NONE NONE R 0 beep_enable alarms NONE RW 0 beeps alarms alarms RW 0 LABEL FEATURE SYMBOL SYSCTL FILE:NR in0 SENSORS_W83781D_IN0 in0:3 in1 SENSORS_W83781D_IN1 in1:3 in2 SENSORS_W83781D_IN2 in2:3 in3 SENSORS_W83781D_IN3 in3:3 in4 SENSORS_W83781D_IN4 in4:3 in5 SENSORS_W83781D_IN5 in5:3 in6 SENSORS_W83781D_IN6 in6:3 in0_min SENSORS_W83781D_IN0_MIN in0:1 in1_min SENSORS_W83781D_IN1_MIN in1:1 in2_min SENSORS_W83781D_IN2_MIN in2:1 in3_min SENSORS_W83781D_IN3_MIN in3:1 in4_min SENSORS_W83781D_IN4_MIN in4:1 in5_min SENSORS_W83781D_IN5_MIN in5:1 in6_min SENSORS_W83781D_IN6_MIN in6:1 in0_max SENSORS_W83781D_IN0_MAX in0:2 in1_max SENSORS_W83781D_IN1_MAX in1:2 in2_max SENSORS_W83781D_IN2_MAX in2:2 in3_max SENSORS_W83781D_IN3_MAX in3:2 in4_max SENSORS_W83781D_IN4_MAX in4:2 in5_max SENSORS_W83781D_IN5_MAX in5:2 in6_max SENSORS_W83781D_IN6_MAX in6:2 fan1 SENSORS_W83781D_FAN1 fan1:2 fan2 SENSORS_W83781D_FAN2 fan2:2 fan3 SENSORS_W83781D_FAN3 fan3:2 fan1_min SENSORS_W83781D_FAN1_MIN fan1:1 fan2_min SENSORS_W83781D_FAN2_MIN fan2:1 fan3_min SENSORS_W83781D_FAN3_MIN fan3:1 temp1 SENSORS_W83781D_TEMP1 temp1:3 temp1_hyst SENSORS_W83781D_TEMP1_HYST temp1:2 temp1_over SENSORS_W83781D_TEMP1_OVER temp1:1 temp2 SENSORS_W83781D_TEMP2 temp2:3 temp2_hyst SENSORS_W83781D_TEMP2_HYST temp2:2 temp2_over SENSORS_W83781D_TEMP2_OVER temp2:1 temp3 SENSORS_W83781D_TEMP3 temp3:3 temp3_hyst SENSORS_W83781D_TEMP3_HYST temp3:2 temp3_over SENSORS_W83781D_TEMP3_OVER temp3:1 vid SENSORS_W83781D_VID vid:1 fan1_div SENSORS_W83781D_FAN1_DIV fan_div:1 fan2_div SENSORS_W83781D_FAN2_DIV fan_div:2 fan3_div SENSORS_W83781D_FAN3_DIV fan_div:3 alarms SENSORS_W83781D_ALARMS alarms:1 beep_enable SENSORS_W83781D_BEEP_ENABLE beep:1 beeps SENSORS_W83781D_BEEPS beep:2 Chip `w83782d' LABEL LABEL CLASS COMPUTE CLASS ACCESS MAGNITUDE in0 NONE NONE R 2 in1 NONE NONE R 2 in2 NONE NONE R 2 in3 NONE NONE R 2 in4 NONE NONE R 2 in5 NONE NONE R 2 in6 NONE NONE R 2 in7 NONE NONE R 2 in8 NONE NONE R 2 in0_min in0 in0 RW 2 in1_min in1 in1 RW 2 in2_min in2 in2 RW 2 in3_min in3 in3 RW 2 in4_min in4 in4 RW 2 in5_min in5 in5 RW 2 in6_min in6 in6 RW 2 in7_min in7 in7 RW 2 in8_min in8 in8 RW 2 in0_max in0 in0 RW 2 in1_max in1 in1 RW 2 in2_max in2 in2 RW 2 in3_max in3 in3 RW 2 in4_max in4 in4 RW 2 in5_max in5 in5 RW 2 in6_max in6 in6 RW 2 in7_max in7 in7 RW 2 in8_max in8 in8 RW 2 fan1 NONE NONE R 0 fan2 NONE NONE R 0 fan3 NONE NONE R 0 fan1_min fan1 NONE RW 0 fan2_min fan2 NONE RW 0 fan3_min fan3 NONE RW 0 temp1 NONE NONE R 1 temp1_hyst temp1 temp1 RW 1 temp1_over temp1 temp1 RW 1 temp2 NONE NONE R 1 temp2_hyst temp2 temp2 RW 1 temp2_over temp2 temp2 RW 1 temp3 NONE NONE R 1 temp3_hyst temp3 temp3 RW 1 temp3_over temp3 temp3 RW 1 vid NONE NONE R 2 fan1_div fan1 NONE RW 0 fan2_div fan2 NONE RW 0 fan3_div fan3 NONE R 0 alarms NONE NONE R 0 beep_enable alarms NONE RW 0 beeps alarms alarms RW 0 sensor1 NONE NONE RW 0 sensor2 NONE NONE RW 0 sensor3 NONE NONE RW 0 LABEL FEATURE SYMBOL SYSCTL FILE:NR in0 SENSORS_W83782D_IN0 in0:3 in1 SENSORS_W83782D_IN1 in1:3 in2 SENSORS_W83782D_IN2 in2:3 in3 SENSORS_W83782D_IN3 in3:3 in4 SENSORS_W83782D_IN4 in4:3 in5 SENSORS_W83782D_IN5 in5:3 in6 SENSORS_W83782D_IN6 in6:3 in7 SENSORS_W83782D_IN7 in7:3 in8 SENSORS_W83782D_IN8 in8:3 in0_min SENSORS_W83782D_IN0_MIN in0:1 in1_min SENSORS_W83782D_IN1_MIN in1:1 in2_min SENSORS_W83782D_IN2_MIN in2:1 in3_min SENSORS_W83782D_IN3_MIN in3:1 in4_min SENSORS_W83782D_IN4_MIN in4:1 in5_min SENSORS_W83782D_IN5_MIN in5:1 in6_min SENSORS_W83782D_IN6_MIN in6:1 in7_min SENSORS_W83782D_IN7_MIN in7:1 in8_min SENSORS_W83782D_IN8_MIN in8:1 in0_max SENSORS_W83782D_IN0_MAX in0:2 in1_max SENSORS_W83782D_IN1_MAX in1:2 in2_max SENSORS_W83782D_IN2_MAX in2:2 in3_max SENSORS_W83782D_IN3_MAX in3:2 in4_max SENSORS_W83782D_IN4_MAX in4:2 in5_max SENSORS_W83782D_IN5_MAX in5:2 in6_max SENSORS_W83782D_IN6_MAX in6:2 in7_max SENSORS_W83782D_IN7_MAX in7:2 in8_max SENSORS_W83782D_IN8_MAX in8:2 fan1 SENSORS_W83782D_FAN1 fan1:2 fan2 SENSORS_W83782D_FAN2 fan2:2 fan3 SENSORS_W83781D_FAN3 fan3:2 fan1_min SENSORS_W83782D_FAN1_MIN fan1:1 fan2_min SENSORS_W83782D_FAN2_MIN fan2:1 fan3_min SENSORS_W83781D_FAN3_MIN fan3:1 temp1 SENSORS_W83782D_TEMP1 temp1:3 temp1_hyst SENSORS_W83782D_TEMP1_HYST temp1:2 temp1_over SENSORS_W83782D_TEMP1_OVER temp1:1 temp2 SENSORS_W83782D_TEMP2 temp2:3 temp2_hyst SENSORS_W83782D_TEMP2_HYST temp2:2 temp2_over SENSORS_W83782D_TEMP2_OVER temp2:1 temp3 SENSORS_W83782D_TEMP3 temp3:3 temp3_hyst SENSORS_W83782D_TEMP3_HYST temp3:2 temp3_over SENSORS_W83782D_TEMP3_OVER temp3:1 vid SENSORS_W83782D_VID vid:1 fan1_div SENSORS_W83782D_FAN1_DIV fan_div:1 fan2_div SENSORS_W83782D_FAN2_DIV fan_div:2 fan3_div SENSORS_W83781D_FAN3_DIV fan_div:3 alarms SENSORS_W83782D_ALARMS alarms:1 beep_enable SENSORS_W83782D_BEEP_ENABLE beep:1 beeps SENSORS_W83782D_BEEPS beep:2 sensor1 SENSORS_W83782D_SENS1 sensor1:1 sensor2 SENSORS_W83782D_SENS2 sensor2:1 sensor3 SENSORS_W83782D_SENS3 sensor3:1 Chip `w83783s' LABEL LABEL CLASS COMPUTE CLASS ACCESS MAGNITUDE in0 NONE NONE R 2 in1 NONE NONE R 2 in2 NONE NONE R 2 in3 NONE NONE R 2 in4 NONE NONE R 2 in5 NONE NONE R 2 in6 NONE NONE R 2 in0_min in0 in0 RW 2 in1_min in1 in1 RW 2 in2_min in2 in2 RW 2 in3_min in3 in3 RW 2 in4_min in4 in4 RW 2 in5_min in5 in5 RW 2 in6_min in6 in6 RW 2 in0_max in0 in0 RW 2 in1_max in1 in1 RW 2 in2_max in2 in2 RW 2 in3_max in3 in3 RW 2 in4_max in4 in4 RW 2 in5_max in5 in5 RW 2 in6_max in6 in6 RW 2 fan1 NONE NONE R 0 fan2 NONE NONE R 0 fan3 NONE NONE R 0 fan1_min fan1 NONE RW 0 fan2_min fan2 NONE RW 0 fan3_min fan3 NONE RW 0 temp1 NONE NONE R 1 temp1_hyst temp1 temp1 RW 1 temp1_over temp1 temp1 RW 1 temp2 NONE NONE R 1 temp2_hyst temp2 temp2 RW 1 temp2_over temp2 temp2 RW 1 vid NONE NONE R 2 fan1_div fan1 NONE RW 0 fan2_div fan2 NONE RW 0 fan3_div fan3 NONE R 0 alarms NONE NONE R 0 beep_enable alarms NONE RW 0 beeps alarms alarms RW 0 sensor1 NONE NONE RW 0 sensor2 NONE NONE RW 0 LABEL FEATURE SYMBOL SYSCTL FILE:NR in0 SENSORS_W83783S_IN0 in0:3 in1 SENSORS_W83783S_IN1 in1:3 in2 SENSORS_W83783S_IN2 in2:3 in3 SENSORS_W83783S_IN3 in3:3 in4 SENSORS_W83783S_IN4 in4:3 in5 SENSORS_W83783S_IN5 in5:3 in6 SENSORS_W83783S_IN6 in6:3 in0_min SENSORS_W83783S_IN0_MIN in0:1 in1_min SENSORS_W83783S_IN1_MIN in1:1 in2_min SENSORS_W83783S_IN2_MIN in2:1 in3_min SENSORS_W83783S_IN3_MIN in3:1 in4_min SENSORS_W83783S_IN4_MIN in4:1 in5_min SENSORS_W83783S_IN5_MIN in5:1 in6_min SENSORS_W83783S_IN6_MIN in6:1 in0_max SENSORS_W83783S_IN0_MAX in0:2 in1_max SENSORS_W83783S_IN1_MAX in1:2 in2_max SENSORS_W83783S_IN2_MAX in2:2 in3_max SENSORS_W83783S_IN3_MAX in3:2 in4_max SENSORS_W83783S_IN4_MAX in4:2 in5_max SENSORS_W83783S_IN5_MAX in5:2 in6_max SENSORS_W83783S_IN6_MAX in6:2 fan1 SENSORS_W83783S_FAN1 fan1:2 fan2 SENSORS_W83783S_FAN2 fan2:2 fan3 SENSORS_W83783S_FAN3 fan3:2 fan1_min SENSORS_W83783S_FAN1_MIN fan1:1 fan2_min SENSORS_W83783S_FAN2_MIN fan2:1 fan3_min SENSORS_W83783S_FAN3_MIN fan3:1 temp1 SENSORS_W83783S_TEMP1 temp1:3 temp1_hyst SENSORS_W83783S_TEMP1_HYST temp1:2 temp1_over SENSORS_W83783S_TEMP1_OVER temp1:1 temp2 SENSORS_W83783S_TEMP2 temp2:3 temp2_hyst SENSORS_W83783S_TEMP2_HYST temp2:2 temp2_over SENSORS_W83783S_TEMP2_OVER temp2:1 vid SENSORS_W83783S_VID vid:1 fan1_div SENSORS_W83783S_FAN1_DIV fan_div:1 fan2_div SENSORS_W83783S_FAN2_DIV fan_div:2 fan3_div SENSORS_W83783S_FAN3_DIV fan_div:3 alarms SENSORS_W83783S_ALARMS alarms:1 beep_enable SENSORS_W83783S_BEEP_ENABLE beep:1 beeps SENSORS_W83783S_BEEPS beep:2 sensor1 SENSORS_W83783S_SENS1 sensor1:1 sensor2 SENSORS_W83783S_SENS2 sensor2:1 Miscellaneous documentation =========================== /PROC ENTRIES ------------- Varies depending on chip type. Most are identical to the lm78 entries. See the lm78 documentation for details. Additional entries not in the lm78: pwm[1-4]: (not on w83781d nor as99127f) Controls the speed of the fans with PWM (Pulse Width Modulation) Valid values: 0 - 255. 255 = max speed. Second value is PWM enable 0/1. sensor[1-3]: (not on w83781d nor as99127f) Controls the sensor type. To change to a different sensor type, for example, do 'echo 2 > sensor1'. Valid values: 1: Pentium II / Celeron diode 2: 2N3904 Transistor in a diode configuration 3435: Thermistor with Beta = 3435. Beta is a measure of sensitivity to temperature. Thermistors with other Betas could in theory be supported after correspondence with Winbond. See below. rt[1-3]: (w83781d only) 32-byte tables controlling the conversion from resistance to temperature for thermistors. For the curious only. Writing to these entries will probably render temperature sensing insane. Only set at initialization; not updated every 1.5 seconds. TO DO: ----- 782d programmable pins NOTES: ----- 783s has no in1 so that in[2-6] are compatible with the 781d/782d. 783s pin is programmable for -5V or temp1; defaults to -5V, no control in driver so temp1 doesn't work. 782d and 783s datasheets differ on which is pwm1 and which is pwm2. We chose to follow 782d. 782d and 783s pin is programmable for fan3 input or pwm2 output; defaults to fan3 input. If pwm2 is enabled (with echo 255 1 > pwm2), then fan3 will report 0. 782d has pwm1-2 for isa, pwm1-4 for i2c. (pwm3-4 share pins with the isa pins) Data sheet updates: ------------------ - PWM clock registers: 000: master / 512 001: master / 1024 010: master / 2048 011: master / 4096 100: master / 8192 Answers from Winbond tech support --------------------------------- > > 1) In the W83781D data sheet section 7.2 last paragraph, it talks about > reprogramming the R-T table if the Beta of the thermistor is not > 3435K. The R-T table is described briefly in section 8.20. > What formulas do I use to program a new R-T table for a given Beta? > We are sorry that the calculation for R-T table value is confidential. If you have another Beta value of thermistor, we can help to calculate the R-T table for you. But you should give us real R-T Table which can be gotten by thermistor vendor. Therefore we will calculate them and obtain 32-byte data, and you can fill the 32-byte data to the register in Bank0.CR51 of W83781D. > 2) In the W83782D data sheet, it mentions that pins 38, 39, and 40 are > programmable to be either thermistor or Pentium II diode inputs. > How do I program them for diode inputs? I can't find any register > to program these to be diode inputs. --> You may program Bank0 CR[5Dh] and CR[59h] registers. CR[5Dh] bit 1(VTIN1) bit 2(VTIN2) bit 3(VTIN3) thermistor 0 0 0 diode 1 1 1 (error) CR[59h] bit 4(VTIN1) bit 2(VTIN2) bit 3(VTIN3) (right) CR[59h] bit 4(VTIN1) bit 5(VTIN2) bit 6(VTIN3) PII thermal diode 1 1 1 2N3904 diode 0 0 0 Author/Maintainer ----------------- Original 781D support: Frodo and Phil 782D/783S support added by: Mark D. Studebaker (mdsxyz123@yahoo.com) Asus Clones ----------- We have no datasheets for the Asus clones (AS99127F and ASB100 Bach). Here are some very useful information that were given to us by Alex Van Kaam about how to detect these chips, and how to read their values. He also gives advice for another Asus chipset, the Mozart-2 (which we don't support yet). Thanks Alex! I reworded some parts and added personal comments. # Detection: AS99127F rev.1, AS99127F rev.2 and ASB100: - I2C address range: 0x29 - 0x2F - If register 0x58 holds 0x31 then we have an Asus (either ASB100 or AS99127F) - Which one depends on register 0x4F (manufacturer ID): 0x06 or 0x94: ASB100 0x12 or 0xC3: AS99127F rev.1 0x5C or 0xA3: AS99127F rev.2 Note that 0x5CA3 is Winbond's ID (WEC), which let us think Asus get their AS99127F rev.2 direct from Winbond. The other codes mean ATT and DVC, respectively. ATT could stand for Asustek something (although it would be very badly chosen IMHO), I don't know what DVC could stand for. Maybe these codes simply aren't meant to be decoded that way. Mozart-2: - I2C address: 0x77 - If register 0x58 holds 0x56 or 0x10 then we have a Mozart-2 - Of the mozart there are 3 types: 0x58=0x56, 0x4E=0x94, 0x4F=0x36: Asus ASM58 Mozart-2 0x58=0x56, 0x4E=0x94, 0x4F=0x06: Asus AS2K129R Mozart-2 0x58=0x10, 0x4E=0x5C, 0x4F=0xA3: Asus ??? Mozart-2 You can handle all 3 the exact same way :) # Temperature sensors: ASB100: - sensor 1: register 0x27 - sensor 2 & 3 are the 2 LM75's on the SMBus - sensor 4: register 0x17 Remark: I noticed that on Intel boards sensor 2 is used for the CPU and 4 is ignored/stuck, on AMD boards sensor 4 is the CPU and sensor 2 is either ignored or a socket temperature. AS99127F (rev.1 and 2 alike): - sensor 1: register 0x27 - sensor 2 & 3 are the 2 LM75's on the SMBus Remark: Register 0x5b is suspected to be temperature type selector. Bit 1 would control temp1, bit 3 temp2 and bit 5 temp3. Mozart-2: - sensor 1: register 0x27 - sensor 2: register 0x13 # Fan sensors: ASB100, AS99127F (rev.1 and 2 alike): - 3 fans, identical to the W83781D Mozart-2: - 2 fans only, 1350000/rpm/div - fan 1: register 0x28, divisor on register 0xA1 (bits 4-5) - fan 2: register 0x29, divisor on register 0xA1 (bits 6-7) # Voltages: This is where there is a difference between AS99127F rev.1 and 2. Remark: The difference is similar to the difference between W83781D and W83782D. ASB100: in0=r(0x20)*0.016 in1=r(0x21)*0.016 in2=r(0x22)*0.016 in3=r(0x23)*0.016*1.68 in4=r(0x24)*0.016*3.8 in5=r(0x25)*(-0.016)*3.97 in6=r(0x26)*(-0.016)*1.666 AS99127F rev.1: in0=r(0x20)*0.016 in1=r(0x21)*0.016 in2=r(0x22)*0.016 in3=r(0x23)*0.016*1.68 in4=r(0x24)*0.016*3.8 in5=r(0x25)*(-0.016)*3.97 in6=r(0x26)*(-0.016)*1.503 AS99127F rev.2: in0=r(0x20)*0.016 in1=r(0x21)*0.016 in2=r(0x22)*0.016 in3=r(0x23)*0.016*1.68 in4=r(0x24)*0.016*3.8 in5=(r(0x25)*0.016-3.6)*5.14+3.6 in6=(r(0x26)*0.016-3.6)*3.14+3.6 Mozart-2: in0=r(0x20)*0.016 in1=255 in2=r(0x22)*0.016 in3=r(0x23)*0.016*1.68 in4=r(0x24)*0.016*4 in5=255 in6=255 # PWM Additional info about PWM on the AS99127F (may apply to other Asus chips as well) by Jean Delvare as of 2004-04-09: AS99127F revision 2 seems to have two PWM registers at 0x59 and 0x5A, and a temperature sensor type selector at 0x5B (which basically means that they swapped registers 0x59 and 0x5B when you compare with Winbond chips). Revision 1 of the chip also has the temperature sensor type selector at 0x5B, but PWM registers have no effect. We don't know exactly how the temperature sensor type selection works. Looks like bits 1-0 are for temp1, bits 3-2 for temp2 and bits 5-4 for temp3, although it is possible that only the most significant bit matters each time. So far, values other than 0 always broke the readings. PWM registers seem to be split in two parts: bit 7 is a mode selector, while the other bits seem to define a value or threshold. When bit 7 is clear, bits 6-0 seem to hold a threshold value. If the value is below a given limit, the fan runs at low speed. If the value is above the limit, the fan runs at full speed. We have no clue as to what the limit represents. Note that there seem to be some inertia in this mode, speed changes may need some time to trigger. Also, an hysteresis mechanism is suspected since walking through all the values increasingly and then decreasingly led to slightly different limits. When bit 7 is set, bits 3-0 seem to hold a threshold value, while bits 6-4 would not be significant. If the value is below a given limit, the fan runs at full speed, while if it is above the limit it runs at low speed (so this is the contrary of the other mode, in a way). Here again, we don't know what the limit is supposed to represent. One remarkable thing is that the fans would only have two or three different speeds (transitional states left apart), not a whole range as you usually get with PWM. As a conclusion, you can write 0x00 or 0x8F to the PWM registers to make fans run at low speed, and 0x7F or 0x80 to make them run at full speed. Please contact us if you can figure out how it is supposed to work. As long as we don't know more, the w83781d driver doesn't handle PWM on AS99127F chips at all. Additional info about PWM on the AS99127F rev.1 by Hector Martin: I've been fiddling around with the (in)famous 0x59 register and found out the following values do work as a form of coarse pwm: 0x80 - seems to turn fans off after some time(1-2 minutes)... might be some form of auto-fan-control based on temp? hmm (Qfan? this mobo is an old ASUS, it isn't marketed as Qfan. Maybe some beta pre-attempt at Qfan that was dropped at the BIOS) 0x81 - off 0x82 - slightly "on-ner" than off, but my fans do not get to move. I can hear the high-pitched PWM sound that motors give off at too-low-pwm. 0x83 - now they do move. Estimate about 70% speed or so. 0x84-0x8f - full on Changing the high nibble doesn't seem to do much except the high bit (0x80) must be set for PWM to work, else the current pwm doesn't seem to change. My mobo is an ASUS A7V266-E. This behaviour is similar to what I got with speedfan under Windows, where 0-15% would be off, 15-2x% (can't remember the exact value) would be 70% and higher would be full on.